SpeedyBee F405 V5 OX32 55A 30x30 Model Aircraft FC&ESC Stack Standard

𝗦𝗽𝗲𝗲𝗱𝘆𝗕𝗲𝗲 𝗙𝟰𝟬𝟱 𝗩𝟱 𝟯𝟬.𝟱×𝟯𝟬.𝟱𝗺𝗺 𝗠𝗼𝗱𝗲𝗹 𝗔𝗶𝗿𝗰𝗿𝗮𝗳𝘁 𝗙𝗹𝗶𝗴𝗵𝘁 𝗖𝗼𝗻𝘁𝗿𝗼𝗹𝗹𝗲𝗿

𝗦𝗽𝗲𝗰𝗶𝗳𝗶𝗰𝗮𝘁𝗶𝗼𝗻𝘀:

● MCU: STM32F405

● IMU (Gyro): ICM42688P

● USB Port Type: New Type-C interface

● Barometer: SPA06-003

● OSD Chip: AT7456E

● Full-featured Bluetooth Tuning: Supported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning.

● Wireless FC Firmware Upgrade: Supported

● DJI Air Unit Connection: Supports 6-pin direct plug-in or solder connection

● Blackbox: Supported, built-in 16MB storage chip

● Input Voltage: 3-6S LiPo battery

● Independent 5V BEC Output: 9 groups (4× +5V pads on front, 1× BZ+ buzzer pad, and 4× +5V pads at the corners for external LEDs). Total output current: ● 1.5A.

● Independent 9V BEC Output: 2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control.

● MCU & Gyro Power: Independent LDO

● 3.3V Output: 1 group (1× 3.3V pad on front)

● 4.5V Output: 3 groups (3× 4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A.

● ESC Signal: M1-M4 pads and 10-pin connector on the back

● Servo Signal: S5-S6 pads on the front

● ESC Telemetry Input: Supported (UART5)

● Betaflight Camera Tuning Pad: Supported (CC pad on front)

● I2C: Supported (GPS connector + pads)

● UART: UART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6-pin); UART4 (GPS pads + front SH1.0-6-pin); UART5 (TLM); ● UART6 (receiver pads + rear SH1.0-4-pin)

● ST LED Pads: Supported, on front G/5V/LED pads; controlled by FC firmware

● Meteor LED Strip Pads: Supported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip.

● Buzzer Pads: Supported

● BOOT Button: [A] Hold BOOT while powering on to force DFU mode for flashing.

[B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1–LED4 are controlled by FC firmware.

● RSSI Pads: Supported

● SmartPort: Not supported

● Supported FC Firmware: Betaflight, INAV, Ardupilot

● Firmware Target Name: SPEEDYBEEF405V5

● Factory Firmware Version: Betaflight 4.5.2

● Configurator Version: Betaflight 10.10.0

● Mounting Holes: 30.5 × 30.5mm (Ø4mm), side opening

● Dimensions: 39mm (L) × 39mm (W) × 4.9mm (H)

● Weight: 8.1g

𝗦𝗽𝗲𝗲𝗱𝘆𝗕𝗲𝗲 𝗢𝗫𝟯𝟮 𝟱𝟱𝗔 𝟯𝟬.𝟱×𝟯𝟬.𝟱 𝟰-𝗶𝗻-𝟭 𝗘𝗦𝗖

𝗦𝗽𝗲𝗰𝗶𝗳𝗶𝗰𝗮𝘁𝗶𝗼𝗻𝘀

● Default Firmware: OX32

● Continuous Current: 55A (per channel) / 220A (4-in-1)

● Maximum Current: 70A (per channel) / 280A (4-in-1)

● TVS Protective Diode: Yes (built-in)

● External Capacitor: 1000µF Solid Capacitor (included in package)

● ESC/Motor Protocol: DSHOT300/600

● Input Voltage: 3-6S LiPo

● Power Output: VBAT

● Current Sensor: Supported

● ESC Telemetry: Supported

● Mounting Holes: 30.5 × 30.5mm (Ø4mm), side opening

● Dimensions: 40.9mm (L) × 44.9mm (W) × 8.0mm (H) (incl. heatsink)

● Weight: 19.1g

● ESC Webpage: https://ox32.oxbot.com/

● Current Meter Note: Supported (Scale=27, Offset=-2644)

𝗠𝗼𝗱𝗲𝗹 𝗔𝗶𝗿𝗰𝗿𝗮𝗳𝘁 𝗦𝘁𝗮𝗰𝗸 𝗦𝘁𝗮𝗻𝗱𝗮𝗿𝗱 𝗣𝗮𝗰𝗸𝗮𝗴𝗲 𝗖𝗼𝗻𝘁𝗲𝗻𝘁𝘀:

1× SpeedyBee F405 V5 Model Aircraft Flight Controller

1× SpeedyBee OX32 55A 32 55A 4-in-1 Model Aircraft ESC

1× Model Aircraft Stack Connector Cable (SH1.0 10pin*25mm)

1× Model Aircraft Stack Connector Cable (SH1.0 10pin*75mm)

1× DJI Air Unit Connector Cable (SH1.0 6pin*80mm)

1× GPS 6pin Connector Cable + 6pin SH1.0 Terminal (SH1.0 6pin*120mm)

1× GPS 4pin Connector Cable + 4pin SH1.0 Terminal (SH1.0 6pin to SH1.0 4pin*120mm)

1× Receiver 4pin Connector Cable (SH1.0 4pin*100mm)

1× XT60 Power Cable (120mm)

4× M3 Model Aircraft Stack Mounting Screws (30mm)

1× Quick Start Guide for Model Aircraft Stack

5× M3 Hex Nylon Nuts

5× M3 Black Silicone Washers

2× Capacitor Heat Shrink Tube

5× Model Aircraft FC Silicone Covers

5× Model Aircraft ESC Silicone Covers

1× 35V 1000uF Solid Capacitor