The SpeedyBee F405 WING APP is a compact yet powerful fixed-wing flight controller designed for RC planes, delivering smooth, reliable flight performance and effortless setup for both beginners and experienced pilots.
৳6,600
SpeedyBee F405 WING FC Board
● MCU: STM32F405, 168MHz, 1MB Flash
● IMU (Gyro & Accelerometer): ICM-42688-P
● Barometer: SPL006-001
● OSD Chip: AT7456E
● Blackbox: MicroSD Card Slot
● UART: 6 sets (USART1, USART2, USART3, UART4, UART5, UART6 - Dedicated for Wireless board Telemetry connection)
● I2C: 1x Used for magnetometer, digital airspeed sensor
● ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed)
● PWM: 12x (11 + 1 “LED” pad)
● ELRS/CRSF Receiver: Supported, connected to UART1
● SBUS: Built-in inverter for SBUS input (UART2-RX)
● LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red), 1x RGB
● RSSI: Supported, Named as "RS"
● Supported FC Firmware:
○ INAV: SpeedyBeeF405WING (default)
○ ArduPilot: SpeedyBeeF405WING
● Weight: 8.9g
SpeedyBee F405 WING PDB Board
● Input Voltage Range: 736V (26S LiPo)
● Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
● Battery Current Sensor: 90A continuous, 215A peak. Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
● TVS Protective Diode: Yes
● FC BEC Output: 5.2V ±0.1V DC, Continuous current 2.4A, Peak 3A. Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED Strip
● VTX BEC Output: 9V ±0.1V DC, Continuous current 1.8A, Peak 2.3A. Voltage adjustable (9V Default, 12V or 5V via jumper). Designed for Analog/Digital Video Transmitter, Camera
● Servo BEC Output: 4.9V ±0.1V DC, Continuous current 4.5A, Peak 5.5A. Voltage adjustable (4.9V Default, 6V or 7.2V via jumper). Designed for Servos
● Weight: 11.4g
SpeedyBee F405 WING Wireless Board
● Wireless Configuration (Long press BOOT button for 6 seconds to switch modes):
○ BLE mode - Connect to SpeedyBee APP
○ Wi-Fi mode - Connect to QGroundControl APP, SpeedyBee APP, MissionPlanner
○ Classic Bluetooth SPP mode - Connect to QGroundControl APP, MissionPlanner
● LED Strip Controller (Short press BOOT button to switch effects, long press 2 seconds to switch modes):
○ 4x WS2812 LED strip connectors, adjustable colors and flashing modes
○ Max 5.2V 1.3A, supports around 70 pcs 5050 WS2812 LED beads
● On-board Battery Level Indicator: 4x RGB indicator LED for battery level display by number of lights
● Weight: 4.2g
Package Includes:
● SpeedyBee F405 WING FC board x1
● SpeedyBee F405 WING PDB board x1
● SpeedyBee F405 WING Wireless board x1
● SpeedyBee F405 WING USB extender x1
● 90 Degree Pin Header (3x12) x1
● Straight Pin Header (1x12) x3
● White Straight Pin Header (1x4) x1
● M2 x 12 Copper Standoff Spacer x5
● M2x4 Small Head Cross Screw x10
● M3x4 mm Silicone Grommets x5
Cables Included:
● 8pin SH1.0 USB Extender Cable (80mm) x1
● 4pin SH1.0 Analog VTX Cable (250mm) x1
● 6pin SH1.0 GPS Module Cable without connector on another end (250mm) x1
● 6pin Digital VTX Cable (250mm) x1
● 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (250mm) x1
● 6pin GH1.25 Telemetry Module Cable (200mm) x1
● 4pin Dupont Single-Head Cable (150mm) x1
● Double-Sided Tape for isolating pins and cables (32x9x1mm) x1
